SEPPES PROJECT / FOOD & SUPPLEMENT WAREHOUSING

An Exterior High-Speed Door Retrofit for a Warehouse Receiving Bay

A food-supplement warehouse needed faster forklift access through its main receiving opening. The existing steel shutter and interior sprinkler pipework occupied the space normally used for a new door. SEPPES kept the shutter in place and mounted a 4,100 × 4,100 mm PVC rapid roll-up door on the outside of the same opening, under the existing canopy.

Exterior face-mountExisting shutter retainedTwo-sided radar
Yellow rapid roll-up door mounted under the existing canopy outside a warehouse receiving entrance
The receiving opening after installation, with the new yellow rapid door mounted outside under the existing canopy.
応用分野
Warehouse receiving bay
Clear opening
4,100 × 4,100 mm
Configuration
External PVC rapid door
引渡し
July 2026
THE PROJECT

A receiving bay needed a fast door without reworking the interior.

The operating problem

Forklifts and goods used the receiving opening throughout the working day. The existing steel shutter was slow for repeated movements and was often left open. The warehouse wanted a faster everyday barrier against airborne dust and outdoor air during wet weather.

The building constraint

The shutter and sprinkler lines occupied the inner face of the opening. Moving the new door to the outer face created a separate installation zone. The project team still had to check the limited space beneath the canopy and make sure the new guides stayed clear of the traffic route.

PROJECT CONFIGURATION

Fit the new assembly around the existing opening.

Design itemProject configurationWhat to confirm at your site
Opening and mountingOne 4,100 × 4,100 mm opening. The head enclosure and side guides were mounted externally under the canopy.Measure the clear width and height separately from the headroom, side room and traffic envelope.
Existing equipmentThe steel shutter stayed in place. The exterior layout avoided relocating the inside sprinkler pipework.Locate the original guides, roller, controls and fire-service elements on the survey drawing and confirm maintenance access.
Curtain and viewYellow PVC curtain with horizontal reinforcement and broad transparent sections.Review exposure to wind and rain, the view across the opening and the required protection for the equipment.
Activation and protectionTwo-sided radar, manual activation options, photoelectric protection and protective posts near the guides.Confirm approach speeds, forklift turning space, detection zones and the separation between opening requests and protective inputs.
ENGINEERING DECISIONS

Check the canopy setback and the forklift approach together.

Use the outside face to free the inside opening

The site check identified the existing shutter and services as the main conflict. Moving the new assembly to the exterior allowed the project to keep the interior equipment in its original positions. SEPPES checked the wall face, fixing points and head space under the canopy before supplying the enclosure.

Make the new door work in daily receiving traffic

The door combined viewing sections with radar activation so drivers could approach from either side. Protective posts were placed by the guides. When reviewing another bay, check where the largest vehicle turns, how it approaches the detection zone and whether the old and new doors can each be maintained.

The same warehouse receiving opening before the exterior rapid door was installed
The same receiving opening before the external door was added. The canopy and adjacent pedestrian entrance identify the opening.
DELIVERY AND HANDOVER

From opening survey to on-site operating checks.

  1. Survey and configuration

    SEPPES reviewed the receiving opening, confirmed the external mounting position and developed the compact head enclosure for the space under the canopy.

  2. Installation at the existing bay

    The installation team fitted the external guides and enclosure and made the electrical connections while retaining the existing shutter.

  3. On-site handover

    The team checked operation, radar coverage and control behavior with the warehouse team. The project record documents handover in July 2026.

PROJECT OUTCOME

What the project delivered

The warehouse gained a separate rapid door for daily use while retaining the original steel shutter. The project shows how an exterior mount can work when the inside face is already occupied. For a similar bay, verify weather exposure, drainage, fixing surfaces and traffic geometry before selecting the door configuration.

PLAN YOUR PROJECT

What to include in an enquiry

Send both faces of the opening

Photograph the canopy, interior services, existing shutter, both jambs and any doors or panels next to the opening. Mark the proposed head and guide positions on the drawing.

Describe the receiving cycle

Share the largest forklift or vehicle, the load envelope, peak movement frequency and the weather exposure. Identify which door handles daily traffic and who will operate and maintain each assembly.

COMMON BUYER QUESTIONS

Questions about this configuration

Can an exterior rapid door be added while keeping the old shutter?

It can be considered if the opening has independent mounting surfaces, maintenance access and a suitable external approach. This warehouse left the existing shutter in place and used the exterior face for the new door.

What measurements matter beneath a canopy?

Record the clear opening, the space above the opening on the external face, canopy projection, side clearances and all nearby pipes or conduits. Check the full height and width available when the door is open.

Why use radar on both sides?

The receiving route had vehicle approaches from both directions. Two-sided activation supports that use, and each detection area should be set up and checked against the actual approach paths.

Can the door control warehouse humidity on its own?

A rapid door can help reduce the time a receiving opening stays exposed. Set any humidity or condensation targets with the warehouse ventilation and building team and verify them under operating conditions.

DISCUSS YOUR REQUIREMENTS

Show us the opening and the equipment around it.

Send a marked layout, opening dimensions, site photographs and your main operating requirement. SEPPES can review the door, mounting conditions and equipment interfaces with your project team.

トップへ